e/h (military m/d55342) www.vishay.com vishay dale thin film revision: 08-jun-11 1 document number: 60018 for technical questions, contact: thinfilm@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 qpl mil-prf-55342 qualified thin film resistor, surface mount chip thin film mil chip resistors feature all sputtered wraparound termination for excellent adhesion and dimensional uniformity. they are ideal in a pplications requiring stringent performance requirements. esta blished reliabilit y is assured through 100 % screening and extensive environmental lot testing. wafer is sawed produ cing exact dimensions and clean, straight edges. note ? specification changed by d.s.c.c. from mil-r-55342 to mil-prf-55342 construction features ? established reliability, r failure rate level (100 ppm), c = 2 ? high purity alumina substrate 99.6 % purity ? wraparound termination feat uring a tenacious adhesion layer covered with an electroplated nickel barrier layer for + 150 c operating conditions ? very low noise and voltage coefficient (< - 25 db, 0.5 ppm/v) ? non-inductive ? laser-trimmed tolerances 0.1 % ? wraparound resistan ce less than 0.010 ? typical ? in-lot tracking less than 5 ppm/c ? complete mil-testing available in-house ? antistatic waffle pack or tape and reel packaging available ? military/aerospace/qpl note ** please see document vishay material category policy: www.vishay.com/doc?99902 typical performance note ? values listed are a guide, refer to mil spec for value/tolerance allowance actual size m55342/02 adhesion layer high purity alumina substrate nickel barrier solder coating passivation resistor film absolute tcr 25 tol. 0.1 standard electrical specifications test specifications conditions material passivated nichrome - resistance range 10 ? to 6.19 m ? - tcr: absolute 25 ppm/c to 300 ppm/c - 55 c to + 125 c tolerance: absolute 0.1 % to 10 % + 25 c stability: absolute ? r 0.02 % 2000 h at + 70 c stability: ratio -- voltage coefficient 0.1 ppm/v - working voltage 30 v to 200 v - operating temperature range - 55 c to + 125 c - storage temperature range - 55 c to + 150 c - noise < - 25 db - shelf life stability: absolute ? r 0.01 % 1 year at + 25 c component ratings case size power rating (mw) working voltage (v) resistance range ( ? ) by characteristics tolerance e (0.1 %) e (1 %, 2 %, 5 %) h, k, m (0.1 %) h, k, m (1 %, 2 %, 5 %) m55342/01 50 40 49.9 to 150k 49.9 to 150k 20 to 150k 20 to 150k m55342/02 125 40 49.9 to 301k 49.9 to 301k 20 to 301k 20 to 301k m55342/03 200 75 49.9 to 649k 49.9 to 649k 10 to 649k 10 to 649k m55342/04 150 125 49.9 to 1.69m 49.9 to 1.69m 10 to 1.69m 10 to 1.69m m55342/05 225 175 49.9 to 3.16m 49.9 to 3.16m 10 to 3.16m 10 to 3.16m m55342/06 150 50 49.9 to 475k 49.9 to 475k 10 to 475k 10 to 475k d55342/07 250 100 49.9 to 1.5m 49.9 to 1.5m 10 to 1.5m 10 to 1.5m m55342/08 800 150 49.9 to 4.02m 49.9 to 4.02m 10 to 4.02m 10 to 4.02m m55342/09 1000 200 49.9 to 6.19m 49.9 to 6.19m 10 to 6.19m 10 to 6.19m m55342/10 500 75 49.9 to 1m 49.9 to 1m 49.9 to 1m 49.9 to 1m m55342/11 50 30 49.9 to 100k 49.9 to 100k 20 to 100k 20 to 100k m55342/12 100 50 49.9 to 258k 49.9 to 261k 10 to 258k 10 to 261k
e/h (military m/d55342) www.vishay.com vishay dale thin film revision: 08-jun-11 2 document number: 60018 for technical questions, contact: thinfilm@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 dimensions in inches case size term. l w t d e m55342/01 b 0.055 0.006 0.025 0.005 0.010 to 0.030 0.010 0.005 0.015 0.005 m55342/02 b 0.055 0.006 0.050 0.005 0.012 to 0.033 0.010 0.005 0.015 0.005 m55342/03 b 0.105 0.007 0.050 0.005 0.015 to 0.033 0.015 0.005 0.015 0.005 m55342/04 b 0.155 0.007 0.050 0.005 0.015 to 0.033 0.015 0.005 0.015 0.005 m55342/05 b 0.230 0.007 0.075 0.005 0.015 to 0.033 0.020 0.005 0.020 0.005 m55342/06 b 0.080 0.006 0.050 0.005 0.015 to 0.033 0.016 0.008 0.015 0.005 d55342/07 b 0.126 0.008 0.063 0.005 0.015 to 0.033 0.020 + 0.005/- 0.010 0.020 + 0.005/- 0.010 m55342/08 b 0.209 + 0.009/- 0.018 0.098 0.005 0.015 to 0.033 0.020 0.005 0.020 0.005 m55342/09 b 0.259 + 0.009/- 0.015 0.124 0.005 0.015 to 0.033 0.020 0.005 0.020 0.005 m55342/10 b 0.105 0.007 0.100 0.005 0.015 to 0.033 0.015 0.005 0.015 0.005 m55342/11 b 0.040 0.005 0.025 0.005 0.010 to 0.030 0.010 0.005 0.015 0.005 m55342/12 b 0.064 0.006 0.032 0.005 0.010 to 0.033 0.012 0.005 0.015 0.005 environmental tests environmental test mil-prf-55342 limits ( ? r ) vishay performance ( ? r ) thermal shock 0.1 % 0.020 % low temperature operation 0.1 % 0.025 % short time overload 0.1 % 0.050 % high temperature exposure 0.1 % 0.009 % resistance to bonding 0.2 % 0.006 % moisture resistance 0.2 % 0.004 % tcr 25 ppm/c < 15 ppm/c life (2000 h at + 70 c) 0.5 % 0.02 % life (10 000 h at + 70 c) 2.0 % 0.04 % d w l t e mechanical specifications resistive element passivated nichrome substrate material alumina chip terminations solder over nickel fused solder sn 63 fscm cage # - 57489
e/h (military m/d55342) www.vishay.com vishay dale thin film revision: 08-jun-11 3 document number: 60018 for technical questions, contact: thinfilm@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note (1) only add a v at the end of part numbe r to specify vishay dale thin film for k/m tcr and tolerance 1 % and higher global part number information new global part numb ering: m55342e06b1c00rts global model tcr characteristic case size termination ohmic value failure rate packaging thin film code (1) m55342 or d55342 (/07 size only) e = 25 ppm/c h = 50 ppm/c k = 100 ppm/c m = 300 ppm/c 01 = 0502 02 = 0505 03 = 1005 04 = 1505 05 = 2208 06 = 0705 07 = 1206 08 = 2010 09 = 2512 10 = 1010 11 = 0402 12 = 0603 b = solderable three digits and a letter. letter identifies tolerance, acts as multiplier and decimal locator. m = 1.0 % per 1000 h p = 0.1 % per 1000 h r = 0.01 % per 1000 h c = non er version standard packaging: bs =bulk 100 min., 1 mult ws =waffle 100 min., 1 mult tape and reel t0 = 100 min., 100 mult t1 = 1000 min., 1000 mult t3 = 300 min., 300 mult t5 = 500 min., 500 mult tf = full reel ( 2k, 4k, or 5k dependent on case size ) per tape and reel document 60034 ts = 100 min., 1 mult special packaging: waffle wi = 100 min., 1 mult (item single lot date code) wp =100 min., 1 mult (package unit single lot date code) tape and reel ti = 100 min., 1 mult (item single lot date code) tp = 100 min., 1 mult (package unit single lot date code) v for k and m tcr w/tolerance ? 1 % multiplier tolerance 1 ? 1 k ? 1 m ? 0.1 % a b c 1 % d e f 2 % g h t 5 % j k l 10 % m n p historical part number example: m55342k 06b5e60r (for reference purposes only) m55342 k 06 b 5e60 r series tcr characteristic case size termination value and tolerance failure rate 5342 06b e m5 1c 0rt 0 s v
document number: 91 000 www.vishay.com revision: 11-mar-11 1 disclaimer legal disclaimer notice vishay all product, product specifications and data ar e subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectivel y, vishay), disclaim any and all liability fo r any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicab le law, vishay disc laims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, incl uding without limitation specia l, consequential or incidental dama ges, and (iii) any and all impl ied warranties, including warran ties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of pro ducts for certain types of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in gene ric applications. such statements are not binding statements about the suitability of products for a partic ular application. it is the customers responsibility to validate that a particu lar product with the properties described in th e product specification is su itable for use in a particul ar application. parameters provided in datasheets an d/or specifications may vary in different applications and perfo rmance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vishays term s and conditions of purchase, including but not limited to the warranty expressed therein. except as expressly indicated in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vishay product co uld result in person al injury or death. customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk and agr ee to fully indemnify and hold vishay and it s distributors harmless from and against an y and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that vis hay or its distributor was negligent regarding the design or manufact ure of the part. please contact authorized vishay personnel t o obtain written terms and conditions regarding products designed fo r such applications. no license, express or implied, by estoppel or otherwise, to any intelle ctual property rights is gran ted by this document or by any conduct of vishay. product names and markings noted herein may be trademarks of their respective owners.
|
